|
|
|
|
4x60W Audio Power Amplifier
ROSSO 460 is a multichannel power amplifier with four high-performance channels using the most recent technologies of digital audio amplification. Each channel delivers a natural and a very wide detailed sound stage, showing the best sonic attributes of solid state (tight and precise bass, dynamics, high reliability) together with the SET tube characteristics (midrange warmth, rich tonalities and a
smooth non-fatiguing listening).
Thanks to the DDP™ (Digital Power Processing) technology from Tripath©, the amplifier combines an audiophile sound with a very high efficiency. That means that a small amount of power is dissipated into heat making feasible the use of a valuable wood enclosure.
Moreover, an electronic crossover with tunable frequency and gain is included on board allowing ROSSO 460 to easily implement a bi-amplification system. You have to just connect a couple of two-way loudspeakers (without passive crossover) and you are ready for
bi-amping. Get rid of all the passive components between the amplifier and the loudspeaker and enjoy the sound clarity of the power direct driving.
Alternatively you can drive a couple of classic full-range loudspeakers with the HF sections of the
ROSSO 460, reserving the LF sections for a passive subwoofer. Other configurations are available according to the chosen setup.
On the rear panel you find two input RCA connectors for the input stereo signal and four binding post for the loudspeakers. The ROSSO 460 is delivered with default crossover setup values, you can otherwise specify your own values before ordering. In any case the parameters can be modified whenever you want through a standard RS232 serial interface.
General specifications
- Large use of SMD components (Surface Mount Devices)
so to have very short interconnection paths and high noise immunity.
- PCBs (Printed Circuit Boards) with wide planes and increased
copper thickness.
- Very short signal paths (output connectors are soldered directly on the printed board -> no cable/wiring effects).
- All the electronic circuits are completely enclosed
into a die cast aluminium box -> high shielding effect
and better EMC performances.
- The electronic components are encapsulated in potting compound to prevent mechanical vibration and to ensure a good heat transfer.
- Low ESR power supply capacitors placed directly across
the supply planes of the PCB.
- Power supply makes use of large tank capacitors and ultra-fast recovery rectifier diodes -> negligible hum and rectification noise.
- Dual-Air-Core output inductors for a crystal sound,
free
of any magnetic core distortion.
- Gold plated inputs and outputs connectors.
- Trigger input connector for remote Power On/Standby.
- Front Touch Sensor for manual Power On/Standby.
- Microprocessor servo assisted power On, pop free outputs.
- Blue LED lamp indicator (Power On/Off/ Standby).
- 4th-order configurable L-R crossover.
- Setup parameters accessible through RS232 interface.
- Hand made wood cabinet finished according to the
best Florentine artisan tradition. Standard finish in
walnut veneer
with
solid walnut edging and
trims
(Italian walnut wood)
.
Other furniture grades
available.
- Laser etched metal plate. Custom plates available
upon request.
- Each ROSSO amplifier is supplied with its own certificate
of
origin and quality.
Technical specifications:
Power output
(single channel) |
60 Watts RMS into 4-ohms
at 0.15% THD+N
40 Watts RMS into 4-ohms at 0.01% THD+N
20 Watts RMS into 8-ohms at 0.01% THD+N |
Note: the overall continuous output power is limited at about 200W by the internal power supply |
Input Impedance |
47 Kohm |
Output offset voltage |
Automatic DC offset trim (±3 mV typ.) |
Frequency response (3dB) |
0.5 Hz - 30 KHz |
Power stage gain |
30 dB |
Signal/Noise Ratio |
100dB |
Setup mode |
1, 2, 3 (default = 1) see crossover setup for more details |
Crossover Frequency |
70 Hz - 3600 Hz (default = 300 Hz) |
Crossover Gain |
±12 dB (default = 0 dB) |
Power supply |
Version /230: 230Vac (50...60 Hz) 250 VA max
Version /115: 115Vac (50...60 Hz) 250 VA max |
Inputs |
- 2 Gold plated RCA sockets
-
1 Trigger 3.5mm jack socket
- 1 IEC switched and fused power inlet
- 1 DB9 female connector (RS232 standard interface) |
Outputs |
- 8 Gold plated loudspeaker terminal posts. Each terminal accepts a 4mm banana plug or up to 6mm diameter cable |
Size |
190 x 220 x
200 mm (width x depth x height) |
Weight |
Approx. 6 Kg |
Options:
- /230 (Power supply 220...240Vac)
- /115 (Power supply 110...130Vac)
- /Sx (Setup mode: see setup for the allowable x values)
- /CFx (Crossover Frequency, x=70,75,80,90,120,180,250,300,400,500,700,1000,1400, 1900,2700,3600)
- /CGx (Crossover Gain (LF section), x=-12,-11...11,12)
- /FM (Mahogany furniture grade)
- /FC (Cherry furniture grade)
Examples of valid codes:
- ROSSO 460 /115
Power supply 110...130Vac
Setup mode = 1 (default)
Crossover Frequency = 300 Hz (default)
Crossover Gain (LF section) = 0 dB (default)
Walnut finished (default)
- ROSSO 460 /115/CF250/CG-3/FC
Power supply 110...130Vac
Setup mode = 1 (default)
Crossover Frequency = 250 Hz
Crossover Gain (LF section) = -3 dB
Cherry finished
<Top> |